Product description:
This is a classic 4-degree-of-freedom machine is inspired by industrial robots. The kit is suitable for guest space, college students, high school students use.
The product is a spare part that is not assembled.
Weight: 360g
Shipping list:
A set of acrylic cutting parts
A pack of screws
Screw M3*20 four
Be careful not to exceed the board, then tighten the nut below.
step 3:The first motor
NOTE:The size of the motor is very close to that of the acrylic, so the force must be slow, so as not to break the acrylic.
NOTE:The gap is the location of the line.
:,M3*8,M3*10M3*12M3.M3*10,.
Special tips: the hole of wood material will be too large, and M3 * 8 screws may be loose on the board directly. It is recommended to use m3 * 10,m3 * 12 screws and M3 nuts for fixation. (exchange with other positions where m3 * 10,m3 * 12 screws are used.)Or just add some glue to fix it
M3*8 screw(double)
Be careful not to tighten the screws too tightly. It will crack the acrylic board too tightly.
Step 4 :Left arm
(1)12mm x 2
(2)8mm x 3
(3) nut x 2
(4) the screw of the steering gear is one length and one shor
Screw M3*8
After power on, the motor is controlled by a rocker to turn clockwise to the end, so that the direction is consistent with the picture.
When installing a stick, add a gasket in the middle.
Yellow to the outside
Power supply 5V 2A charger
Turn to the rudder counter clockwise
Clockwise steering wheel
Step 5 :Right arm
12mm X 3
8mm x 2
6mm x 1
After power on, the steering wheel is inserted into the circuit board, turning clockwise to the same direction as the picture.
12mm x 2
6mm x 1
Nut x2
First put on the shell and then install the screws. When tightening, do not tighten too tightly.
The right arm is put on the shell first and then tightened.
Step 7: right arm + chassis
Tighten the screw and tighte
This is a classic 4-degree-of-freedom machine is inspired by industrial robots. The kit is suitable for guest space, college students, high school students use.
The product is a spare part that is not assembled.
Weight: 360g
Shipping list:
A set of acrylic cutting parts
A pack of screws
Screw M3*20 four
Be careful not to exceed the board, then tighten the nut below.
step 3:The first motor
NOTE:The size of the motor is very close to that of the acrylic, so the force must be slow, so as not to break the acrylic.
NOTE:The gap is the location of the line.
:,M3*8,M3*10M3*12M3.M3*10,.
Special tips: the hole of wood material will be too large, and M3 * 8 screws may be loose on the board directly. It is recommended to use m3 * 10,m3 * 12 screws and M3 nuts for fixation. (exchange with other positions where m3 * 10,m3 * 12 screws are used.)Or just add some glue to fix it
M3*8 screw(double)
Be careful not to tighten the screws too tightly. It will crack the acrylic board too tightly.
Step 4 :Left arm
(1)12mm x 2
(2)8mm x 3
(3) nut x 2
(4) the screw of the steering gear is one length and one shor
Screw M3*8
After power on, the motor is controlled by a rocker to turn clockwise to the end, so that the direction is consistent with the picture.
When installing a stick, add a gasket in the middle.
Yellow to the outside
Power supply 5V 2A charger
Turn to the rudder counter clockwise
Clockwise steering wheel
Step 5 :Right arm
12mm X 3
8mm x 2
6mm x 1
After power on, the steering wheel is inserted into the circuit board, turning clockwise to the same direction as the picture.
12mm x 2
6mm x 1
Nut x2
First put on the shell and then install the screws. When tightening, do not tighten too tightly.
The right arm is put on the shell first and then tightened.
Step 7: right arm + chassis
Tighten the screw and tighte
