?10" solid rubber tire - front and rear scooter trye - replacement tire?10 x 2.5 - 6.5 ?? 60/70-6.5 ? ?
?Explosion proof ?Stab-proof ?Non-slip ?Wear resistant.
?Fit for:
?Gotrax G5/ G6/ G MAX Eclipse
?Ninebot MAX G30P G30LE/ G30E G30LE/ G30D G30LD
?Zero 10X
?Hiboy Max 3
?Titani Pro
?Varla Eagle One
?Hover 1 Alpha
?JueShuai X48
?OKAI neon pro/ ES520B
?Yume D4
?Inmotion L9
?Gyrror X8
?Wheelspeed 1/ Pro
?Kaabo skywalker 10H/ Mantis Pro
?etc.
If your scooter model is not available above, please send us your scooter model to help you confirm if our tires are suitable for your scooter.(*^?^*)
?Please note: 10x2.5 inch is the size of the tire after it is mounted to the hub, not the actual size of the physical object. The above data are manual measurements, and the allowable error is 0.1-0.5cm/0.03-0.19 inch.
?The installation process:
1.Add some lubricant on the rim of the wheel. This should manage the amount of friction that will be involved during the fitting.
2. You need to soften the solid wheel before fitting it: Boil some water to about 100ºC in a pot large enough to fit the tire. Put it in (make sure that it is wholly immersed) then leave it for ten minutes.
3. As an alternative, you can heat the tire in a microwave for three minutes, checking it after every minute.
4. Once the wheel is soft enough, remove it and fit the rim into it. Let it cool for five minutes.
5. Fasten the nut and the other screws (while replacing the plastic cover) on both sides. This is basically the reverse of the initial process of removing the wheel.
?NOTE?If you still don't know how to install your tires, please contact us and we will give you an easy installation tutorial video, a complete service system.
Your scooter is now ready to go!!!
?Explosion proof ?Stab-proof ?Non-slip ?Wear resistant.
?Fit for:
?Gotrax G5/ G6/ G MAX Eclipse
?Ninebot MAX G30P G30LE/ G30E G30LE/ G30D G30LD
?Zero 10X
?Hiboy Max 3
?Titani Pro
?Varla Eagle One
?Hover 1 Alpha
?JueShuai X48
?OKAI neon pro/ ES520B
?Yume D4
?Inmotion L9
?Gyrror X8
?Wheelspeed 1/ Pro
?Kaabo skywalker 10H/ Mantis Pro
?etc.
If your scooter model is not available above, please send us your scooter model to help you confirm if our tires are suitable for your scooter.(*^?^*)
?Please note: 10x2.5 inch is the size of the tire after it is mounted to the hub, not the actual size of the physical object. The above data are manual measurements, and the allowable error is 0.1-0.5cm/0.03-0.19 inch.
?The installation process:
1.Add some lubricant on the rim of the wheel. This should manage the amount of friction that will be involved during the fitting.
2. You need to soften the solid wheel before fitting it: Boil some water to about 100ºC in a pot large enough to fit the tire. Put it in (make sure that it is wholly immersed) then leave it for ten minutes.
3. As an alternative, you can heat the tire in a microwave for three minutes, checking it after every minute.
4. Once the wheel is soft enough, remove it and fit the rim into it. Let it cool for five minutes.
5. Fasten the nut and the other screws (while replacing the plastic cover) on both sides. This is basically the reverse of the initial process of removing the wheel.
?NOTE?If you still don't know how to install your tires, please contact us and we will give you an easy installation tutorial video, a complete service system.
Your scooter is now ready to go!!!
