2pcs E-Simpo G23 3W LED Bulb PLS-7W Replacement G23d 2P LED PL Retrofit Horizontal Recessed Down Light Plug Play for INDUCTANCE/MAGNETIC ballast Daylight 6000K 85-135V AC (Cold White, 4.2in/107mm 3W)
Specification
Input Voltage: 85-135V AC
Power: 3W LED Dimmable
CRI>82
Base: G23d-2, G23 both fit. NOT Gx23 please identify the light socket base before buy. GX23 G23 both 2Pin in Parrall, but GX23 is with double tab, G23 single tab
Brightness: 3W: 300-350Lumens; Color Temperature: Warm White 3000-3500K; Cold White 6000-6500K Please check the PL Lamp fixture or table light fixture for allowed install length before you decide. 107mm long 4.2" Application: 3W is used to Replace 2-Pin CFL PLS-7W. Great G23 led replacement lamp for OttLite fluorescent table lamp, and replace PLS-7W or Osram 7w,clean bright non flickering light, it turned it on instantly, no buzzing noise. Note: 1. Please check if the inside ballast is inductive ballast or electronic ballast; 2. If it is inductive ballast, you can use this LED lamp directly, just plug and play. 3. If it is electronic ballast, the led driver can not work compatibly, so you have to bypass the electronic ballast(cut off the transformer). Otherwise the LED Lamp witll get flicking, burnt, smell, damaged.
How to bypass the ballast? 1. Turn Off the Power. 2. Find the Ballast. Usually it is embeded inside the ceiling fixture. Pls pull off the existing PL lamp, reflector. Leave wire in junction box. and find the ballast. 3. Normally, the Ballast has a black and white wire on the input side. It also has two red and two blue output wires. To bypass this ballast, please cut all the Input and output wires, so total 6 wires cut. 4. Then,connect two red wires to black wire. connect two blue wires to white wire. ballast bypassed!
Base: G23d-2, G23 both fit. NOT Gx23 please identify the light socket base before buy. GX23 G23 both 2Pin in Parrall, but GX23 is with double tab, G23 single tab
Brightness: 3W: 300-350Lumens; Color Temperature: Warm White 3000-3500K; Cold White 6000-6500K Please check the PL Lamp fixture or table light fixture for allowed install length before you decide. 107mm long 4.2" Application: 3W is used to Replace 2-Pin CFL PLS-7W. Great G23 led replacement lamp for OttLite fluorescent table lamp, and replace PLS-7W or Osram 7w,clean bright non flickering light, it turned it on instantly, no buzzing noise. Note: 1. Please check if the inside ballast is inductive ballast or electronic ballast; 2. If it is inductive ballast, you can use this LED lamp directly, just plug and play. 3. If it is electronic ballast, the led driver can not work compatibly, so you have to bypass the electronic ballast(cut off the transformer). Otherwise the LED Lamp witll get flicking, burnt, smell, damaged.
How to bypass the ballast? 1. Turn Off the Power. 2. Find the Ballast. Usually it is embeded inside the ceiling fixture. Pls pull off the existing PL lamp, reflector. Leave wire in junction box. and find the ballast. 3. Normally, the Ballast has a black and white wire on the input side. It also has two red and two blue output wires. To bypass this ballast, please cut all the Input and output wires, so total 6 wires cut. 4. Then,connect two red wires to black wire. connect two blue wires to white wire. ballast bypassed!
